Reasons Your Fiat panda key 500 Key Fob Won't Work

A key fob from fiat 500 key button replacement 500 is a handy way to open the doors and begin the car. There are many reasons why the key fob might stop working. This includes a dead battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat 500 key Fiat Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob not working. Modern key fobs have a limited operating range and should be within some feet of the vehicle to function. If you're far from your vehicle and press the key fob button, the car won't respond and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin-cell battery (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. They are typically available in your local hardware store, or online.

After you've changed the battery on the coin cell It is possible to test it by standing near your Fiat 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switches.

If the spare key for fiat 500 fob won't function after replacing the battery, it could be damaged by water that blocks it from communicating with the receiver module inside your vehicle. Water damage can happen in a variety of ways, from the slightest splash to submerging the fob into salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this fails, you'll need to have the fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and then fail. It's not a good idea to let the fob get wet however, don't give it up if you accidentally drop it in water or forget to take it out of your pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Test the fob afterward to determine if it's functioning. If the key isn't working, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is older and is not programmed for your vehicle You will need to replace it completely. This is an easy process that can be handled by a professional automotive locksmith. The locksmith will need the key to be cut to match your car's ignition. The locksmith will also need to program your fob into the car's system. This is a simple and inexpensive process that can be completed within the next day.

Receiver Module Issues

Your 500 key fob may stop working because it is out of range. The remote has a range of 30 feet, which means should you be too far from your car it won't be able to respond to your commands. You can solve this problem by moving the remote closer to your vehicle until it responds.

If your fob doesn't work after replacing the battery in the coin, also known as a "button", "watch" or "button" it may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob will fix the problem. You can find directions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

You may need to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances the fob might become disconnected from your vehicle due to software issues or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances, they may need to install the software again in your body control module, as well.

Interference

In addition to a dead battery on a coin the key fob could not be receiving or transmitting the signal due to interference. This can occur when the keyfob is located in close proximity to a radio transmitter like a cell phone or radar detector. The key fob might not function due to a bad connection to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

There's a simple method to reset the 500's onboard system including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computers. This could help the key fob to function again. If the problem persists, you should consult an expert certified technician. They will be able to determine the root of any issues.