Reasons Your fiat 500 abarth key fob replacement 500 Key Fob Won't Work

A key fob for the fiat doblo key fob programming 500 is a convenient method to unlock the doors and start the car. There are a myriad of reasons the fob may stop working. This could be due to a dead coin battery or water damage, receiver module problems, and interference.

This listing is for an NEW replacement key fiat 500 fiat ducato key programming; just click the next web page, Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not work is a dead battery. Modern key fobs come with a restricted operating range, and must be within just a few feet of the car to operate. If you are not within your vehicle and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the coin cell battery (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. You can find them in the local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The car should blink its parking lights and the key fob should work the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it may have water damage that prevents it from communicating with the receiver module in your car. Water damage can occur in a number of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture out. If this isn't working, you'll have to get your fob changed by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to short and then die. It's not a good idea to get the fob wet but don't give up in the event that you accidentally drop it in the water or don't take it out of your pants pocket.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Then check the fob to see if it works. If the key still doesn't function, it may need to be programmed again. This is typically handled by a professional or dealer auto locksmith.

If the key you have is older and not programmed to work with your vehicle You will need to replace it completely. This is a straightforward process which can be accomplished by a professional automotive locksmith. The locksmith will require the key cut to match your vehicle's ignition. They'll also need to reprogram the fob for your vehicle's system. This is a fast and affordable process which can be completed in the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob won't be functioning is because it's out of range. The remote has a maximum range of 30 feet, so when you're too far from your car, it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.

If your fob doesn't work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button" it may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob will fix the issue. You can find directions on how to do this for most automobiles by searching YouTube or reading the owner's manual.

It is possible to replace the metal retaining clips that hold the coin battery in place. If they lose tension it could hinder the coin battery from being seated properly and can cause the remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit signals. This can occur when the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons why the key fob might not work may be a lack of connection to the buttons and internal chip, or water damage.

If the key fob suddenly stopped working, out of the blue, or after trying every option at home to solve it e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computer system, which can help you the key fob to function again. If the issue continues, you should consult an expert technician. They can identify the exact cause of any problems.